Antique and Vintage Hinges
Take a look at the round ring and cotter pin in your photo - to me it looks as if those may be hand -made. From to bronze was the metal of choice for the manufacture of artistic hardware. Some are quite attractive but I believe that it's worth the effort to use all antique components.
As it turned out, using them as door pulls was the right idea, and we love them! The presence of brass hardware at all also tells a tale. Antique Pine Interior Door. This can mean that they were handcrafted prior to or so.
Antique Doors in Mexico
Is there any way that I can tell how old they are please? Antique Octagonal Newel Post. How are antique doorbells installed? Using a drill, make holes through the door for the spindle and the key hole.
Machine made rings or cotter pins were made from round wire. Antique Upholstered Swinging Door. Almost all the locks sold here are reversible by simply removing the lock body cover and turning the strike over. Add a vertical center line to aid drilling.
If you find these hand finished screws in furniture, investigate other aspects of the pieces to see if they match the screws in age. The site the door knobs were founds was the site in Brisbane, Australia, of the original s house that was replaced in by another house, which is the only indication that I have of the ages. The first screws were crafted in the s by blacksmiths using square nail stock that was heated and pounded until it was somewhat round.
Door Age Door Locks Knobs Hinges Hardware as Indicators of Building Age
Antique and Vintage Hinges
Below you can refine search results. Looking at the joinery, or the way a piece of antique furniture is put together, will provide many clues that help in determining the age. As discussed above, behavior mindless this is especially evident on the back or underside of pieces made prior to the mids.
Sit the lock in the mortise and mark the faceplate on the door edge. It's usually very hard to tell the difference but, in general, brass will have a yellow color and bronze will have a more rose color. Field inspection worksheets are included at the back of the volume.
The twist type bells can be placed on an exterior wall next to the door with minor modification by simply adding length to the square spindle. The square cross-section knob shaft, now badly rusted and exfoliating, looks like iron. Antique Chestnut Interior Door. That's where all the broken cast iron hinges come from!
How do I install a rim lock? There is also some evidence that Australia had some metalworking going on before the arrival of Europeans, though that would not of course be likely to pertain to the door knobs in your photos. Honing your wood identification skills can really pay off in this area. For the actual installation, dating online first lay the lock body in position with lock at the edge of the door and mark the location of the doorknob spindle and key hole on the door. Would highly recommend - price and shipping could not be beat!
Tips for Dating Old Pieces Made in America
Wooden Keyhole Escutcheon, Diamond, Oak. Antique Oak Veneer Pantry Door. Antique Birch Interior Door. Looking at the bottom or back of a piece, or inside its doors and drawers, can provide important clues about whether or not a piece of old furniture was machine cut or crafted by hand. Drill another two holes for the key and chisel out any remaining wood between the two holes.
We re-faced the exterior to shingles previously clapboard and we are keeping the plastered walls and putting your hinges on all of the interior doors. Make the keyhole the correct shape by enlarging the lower half. This hinge uses the weight of the door to swing the door shut. Can you circa date solely on the type of wood used? Here are a few from our inventory.
- How do I install a mortise lock?
- Silk, wool, and cotton have been spun and woven into a variety of damasks, satins, and brocades with many different patterns.
- If the door has a big round ugly hole it will need to be filled first.
Antique Interior Oak Doors. Antique hardware catalogs always reflect what kind of metal was used for a specific piece. Can antique doorknob locksets be installed on modern doors? On painted doors just putty and paint.
Also, never use a screw gun or drill! Bathroom Door Pulls For the French doors on our new bathroom, it was a challenge to find the right door knobs. It had started to rust and that made us very unhappy.
Stand on the side of the door where you can see the barrel of the hinges. Drill straight through the door for the spindle. Screw the rosette and key escutcheon to the other side of the door.
If the spindle is loose, just replace it. Ready for the hard stuff now? Hopefully you can help me, or know someone who can, date my door knobs please.
Our second photo above illustrates a lock and key in a hotel in Real de Catorce, Mexico. If you have a steel door, either use modern hardware or replace the door. Antique Poplar Double Door Set.
The following are questions I am frequently asked - with ANSWERS
The shipment arrived quickly and is perfect. Manually operated hand saws left a straighter pattern in comparison. Any help that you can give is greatly appreciated.
Look for hammer marks and surface or shape irregularities beyond those ascribed to rust or corrosion or usage-wear that may be from having been worked by hand tools such as a hammer. Mark the top and bottom of the lock casing on the door edge. Weonards, dating headlines that get Herefordshire U. To be historically correct a slotted screw is necessary.
- If you have a piece with brasses, it's most likely pres or a revival piece from the late s on.
- Then ease out the indentations made by the chisel to give you your recess.
- But remember that the appearance of new technology across a huge continent is never simultaneous nor uniform.
- Windsor Cabinet Latch, Antique Nickel.
- The round ring and cotter key look to me to have been fabricated out of iron and possibly copper or brass for the pin.
Antique Fir Swinging Door. Tall Antique Interior Door. The year it was made can also give a good indication of which is which. Again, fill in any holes that may already be in your door.